INSTRUCT

WHAT IS THE APPLICATION? LEARN ABOUT STRUCTURE AND HOW TO DESIGN NAIL

What is single nail? Structure and design of single foundation is what? You will know about these when you read this article by MOIVAONHATOI.

Nhà được tạo lên từ móng, vậy bạn có biết móng đơn (kiểu móng đơn giản nhất) là gì không? Hay bạn có bao giờ tò mò về cấu tạo của móng đơn, và cách thiết kế nó không? Nếu thắc mắc những vấn đề này thì bạn hãy đọc ngay bài viết dưới đây của MOIVAONHATOI để hiểu thật rõ về móng đơn là gì nhé.

WHAT IS NAIL?

Single nails have another name, cup nails, which support one or a cluster of columns. Commonly used for buildings under 3 floors. Single foundations are located at the base of the column, which can be hard, individual or soft nails and often reinforced with cajeput.

WHAT IS THE STRUCTURE OF NAIL?

Cấu tạo của móng đơn rất đơn giản, được tạo thành từ một bê tông cốt thép dày và tạo hình trụ duy nhất. Đối với các công trình công nghiệp người ta tận dụng phần đáy móng được đặt lên trên một lớp đất tốt với chiều sâu khoảng 1m. Điều này giúp tạo ra 1 bề mặt bằng phẳng để tránh sự thay đổi giữa các vùng giáp ranh với đất tốt và đất xấu. Tránh sự nở của các loại đất do bão hòa với nước.

In xây dựng thì móng được liên kết với một hoặc nhiều tảng hệ thống dầm. Có tác dụng chống đỡ hệ thống  tường xây bên trên. Ngoài ra còn có tác dụng giằng các móng cốc để tránh hiện tượng lún, lệch giữa các đài móng.

See more: Quotations for construction of townhouses Just fill in the area, the number of floors

WHAT IS SUSTAINABLE STEEL STRUCTURE?

Single-nailed steel will be of the highest quality steel. Single foundation reinforcement can be machined in the field or in factories. But to comply with technical drawings specifications. Clean all site surfaces, assemble according to the design drawings.

In welding - welding, it is necessary to ensure firm joints. Avoid the heat to burn the formwork. The rebar must be ensured free of mud, grease, and rust. If the case of iron bars are flattened or cut, the cross-section should not exceed 2%.

The welds must ensure> 10d

Forced concatenation> 30d

The solder joint needs to be cleaned

Steel ends should be protected with plastic bags.

COCONUT NAIL SALON

To construction móng đơn cừ tràm vững chắc cần xử lý một nền móng cứng cáp trước đã. Dùng cừ tràm để gia cố là biện pháp được sử dụng nhiều trong xây dựng. bởi độ tiện lợi cùng với giá thành khá rẻ so với vật liệu tổng hợp khác. Móng cốc là đơn vị chịu tải trung gian. Truyền trọng lượng từ công trình xuống lớp đất nền. Và lớp đất nền này được gia cố bằng các cọc cừ tràm. Đã có hàng trăm công trình tại TP.HCM sử dụng móng cừ tràm vẫn đang đứng vững và có đánh giá an toàn cao.

WHAT IS THE DESIGN OF THE NAIL?

Tùy theo công trình thi công mà các nhà thầu sẽ lựa chọn tính toán và thi công cho từng loại. Cùng một cách tính toán nhưng sẽ chia ra chi từng chi tiết cho công trình. Móng đơn dưới cột làm bằng đá hộc, bộ phận này được tính toán theo cường độ của vật liệu xây móng. Móng cốc (đơn) dưới tường được đặt cách nhau từ 3 đến 6m dọc theo bức tường và đặt dưới các tường góc nhà. Tại các tường ngăn chịu lực và tại các chỗ có tải trọng tập trung trên các móng.

Many designs will have different advantages and disadvantages, many plans will arise. Depending on that, engineers will design more details.

TAM TAM NAIL DESIGN

The cause of the eccentricity is that the problem posed is the balance of the foundation block. Engineers can create this balance in the following ways:

  • Ground jets possess a triangular or trapezoid form. Then the center of this jet system will move compared with the center of the radio. The base station balance will be established when the center of gravity of this jet system coincides with the setpoint of the force system transmitted down from the column. This approach is often less efficient or unusable in the case of a large eccentric torque. Then the jet is usually triangular, to balance as above, the maximum mobilized foundation width is only 3/2 column width. If the longitudinal force is large, it cannot be superficial to satisfy ground pressure conditions.
  • You can use a human toenail or a propeller to reduce eccentricity. In addition, there are many opinions that it is necessary to add anti-roll columns, but calculations think that the presser foot style is correct.

NAIL DESIGN STANDARDS

  • The selection of construction methods, construction of coke foundations - single must consider geological survey data. Additional calculation must be carried out if the actual engineering geology of the construction site is inconsistent with the calculations in the single foundation design.
  • All materials, supporting machinery and structural parts used in the construction of cup foundations (single) must satisfy the design requirements.
  • When building single foundations, it is necessary to have the technical inspection of the agency.

See more: See feng shui direction By age, year of birth

COMPUTER NAIL DESIGN

Biến dạng nền không quá lớn thì chúng ta áp dụng lý thuyết đàn hồi tính các đặc trưng biến dạng. Tận dụng khả năng làm việc của nền trong giai đoạn biến dạng tuyến tính. Công thức tính móng đơn theo đúng quy trình kỹ thuật:

When the load is right to center of gravity: P ≤ R

When the eccentric load: P ≤ 1.2 R (P, P: average and maximum foundation pressure; R: standard strength of the ground)

R = m (A .γ.b + B.q + Dc) (3)

Inside

b: Width of foundation base

q: Side load of foundation

c: Unit cohesion of the ground layer

A, B, D: The coefficients depend on the angle of the internal friction of the soil.

m: Coefficient of working condition of single foundation

CONSTRUCTION SINGLE DESIGN

Understand what single foundation is, as well as the structure of the foundation, so what should we pay attention to when constructing the single foundation design? MOIVAONHATOI would briefly list as follows:

  • Site preparation: Before construction, site preparation, labor, machinery, raw materials, ... are required.
  • Leveling: Conducting leveling for the foundation construction process
  • Preparation, reinforcement work: Steel selected and correctly machined with all criteria

Above are some basic knowledge to help you understand what a single nail is, as well as its structure and design. Hope this information has helped you clear your questions, and maybe you will need to use them during construction. upgrade house .

Muốn nhận tư vấn về thiết kế – thi công công trình nhà ở, xin vui lòng liên hệ:
MV CONSTRUCTION COMPANY - INVITED TO MY HOUSE
Hotline: 0908.66.88.10 - 09.0202.5707
Address: 201 Bà Triệu, Hai Bà Trưng District, Hà Nội
Email: gdmoivaonhatoi@gmail.com
Website: https://moivaonhatoi.com/

en_USEnglish